WT-5800 C05UK

Wireless Receiver

WT-5800 C05UK

The wireless tuner WT-5800 is a PLL-synthesizer controlled double superheterodyne true diversity tuner to be used in UHF wireless systems. It employs a compander noise reduction circuit to minimize the influence of the ambient RF noise.

Automatic frequency scan
Integrated squelch function
Ideally suited for fixed installations such as in event locations, multi-purpose and sports halls, plenary and conference venues, churches, auditoriums etc.
System always select the stronger of the two antenna signals for further processing
Setup with up to 16 simultaneously operating receivers possible
Two antenna distribution outputs allow to simply loop through the antenna signals

Specifications Equipment A&E Specs Downloads

*1 0 dB = 1 V

Power Source

AC mains (Supplied AC adapter must be used)

Power Consumption

250 mA (12 V DC)

Frequency Range

576 - 865 MHz, UHF

Channel Selection

64 selectable frequencies

Receiving System

Double super-heterodyne

Diversity System

Space diversity (true diversity)

Mixing Output

MIC/LINE (selectable): –60 dB*1 (MIC)/–20 dB*1 (LINE), 600 Ω
Phone jack (unbalanced), 600 Ω XLR-3-32 type connector (balanced)

Mixing Input

–20 dB*1, 10 kΩ, unbalanced, phone jack

Antenna Input

75 Ω, BNC (phantom powering for antenna), 9 V DC, 30 mA (max)

Antenna Output

75Ω, BNC (Gain 0 dB)

Receiving Sensitivity

90 dB or more, Signal to Noise ratio (20 dBμV input, 40 kHz deviation)

Harmonic Distortion

1% or less (typical)

Squelch Sensitivity

16 – 40 dBμV variable

Squelch System

Using together of noise SQ, carrier SQ and tone SQ

Tone Frequency

32.768 kHz

Indicator

Audio (6 steps), RF (6 steps), ANT A/B, Audio (peak), Battery alarm

Channel Check

Usable frequencies scanning

Signal to Noise Ratio

110 dB or more (A-weight, unbalanced output)

Frequency Response

100 Hz – 15 kHz, ±3 dB

Operating Temperature

–10°C to +50°C (14°F to 122°F)

Operating Humidity

30 % to 85 %RH

Finish

Resin, black

Dimensions

210 (W) x 44 (H) x 205.1 (D) mm (8.27" x 1.73" x 8.07")

Weight

700 g (1.54 lb)

Included Accessories

AC adapter

Please download Datasheet to access full specifications.

Optional Accessory

MB-WT3

MB-WT4

YW-4500

The wireless receiver shall have 64 selectable channels and a built-in scanner function to scan the RF environment and indicate available channels. The receiving method shall be double super-heterodyne using signal strenth-comparative antenna switching diversity. Specifications shall include a S/N ratio of greater than 110 dB (A-weighted), harmonic distortion of less than 1% and frequency response of 100 - 15k Hz, +/-3 dB. The receiving sensitivity shall be greater than 90 dB with 20 dBµV input and 40k Hz deviation. Squelch types shall be carrier, noise and tone key with a variable squelch sensitivity of 18 - 40 dBµV and a 32.768k Hz tone key frequency. The receiver shall have two antenna inputs, each with BNC-type connectors, 75 ohm impedance and 9 VDC, 30 mA, available for remote antennas. The unit shall also have two antenna outputs, with BNC-type connectors, 75 ohm impedance, and 0 dB gain, to provide antenna distribution to a maximum of two additional receivers. The audio outputs shall be balanced type with XLR-M jack and sensitivity of -60 dB / 1 mV, and unbalanced type with 1/4" phone jack and sensitivity of -20 dB / 100 mV, both with an output impedance of 600 ohms. A Mix Input, unbalanced type with 1/4" phone jack with an input impedance of 10k ohms and sensitivity of -20 dBV / 100 mV shall allow the connection of the output of a second receiver or other audio source to be mixed with the main receiver output signal. The front panel shall include an LCD for RF and AF monitoring as well as frequency setting and scanner functions. Front panel LED's shall include antenna A / B reception status, low battery indication, and an AF peak indicator that lights at 3 dB below clipping. Front panel controls shall include Up, Down, and Set keys for menu navigation as well as Power and Volume. The wireless receiver shall be powered from the AC mains using a supplied AC-DC adapter with a power consumption of 250 mA (12 VDC). The unit shall operate within a temperature range of -10° C to +50° C (+14° F to +122° F).Unit construction shall be black resin with dimensions (W x H x D) of 210 x 44.6 x 205 mm (8.27” x 1.76” x 8.1”) and weight of 700 g (1.54 lbs.). Included accessories shall be two whip antennas and an external AC-DC adapter.Up to two units shall be rack-mountable in one standard 19" rack height with an optional rack-mount kit.
The wireless receiver shall be the TOA model WT-5800.

Please sign in to access further technical materials such as software, firmware or EASE files.